 |
(541) 474-2879 phone 10am-6pm Mo-Thu No Sales Tax |
|
||||
|
HOME | YOUR ORDER | EMAIL US | ORDERING INFO | | |
||
Camburg Engineering Adjustable Front Coilover Shocks
and Uni-Ball Upper Control Arms for
2005-Current
Toyota Tacoma 4x4 and PreRunner
(REAR SHOCKS AND ACCESSORIES SHOWN BELOW, TOO!)
Camburg Engineering offers their 2.5" adjustable racing style front
coilover shocks for 2005-current Toyota Tacoma 4x4 and PreRunner. These shocks can be
adjusted from 0"-3" of lift. Each shock set includes a spanner
wrench for adjustment, and a sway bar relocation kit. They are rebuildable and revalveable. They have a 200psi
nitrogen charge. They have full spherical bearing type upper and lower mounts. These US made shocks feature top notch machining and design,
7/8" Nitrosteel shafts and red anodizing. They bolt on your truck with no
modifications and work well with your factory control arms. Optionally, we have
Camburg Upper Control Arms listed below.
2.5" Coilover Shock
Set:
925.00/pair
____________________________________
CAMBURG UPPER CONTROL ARMS (Not mandatory but a nice addition.)
Camburg Uni-Ball Upper Control Arm Set:
639.00/pair
" 11/12/08: We’ve taken our
successful uniball upper a-arms to the next level. Our performance upper arms
now use a much larger and stronger 1.25" uniball bearing. This bearing
allows for more mis-alignment for maximum wheel travel and uses our new flush
mount hardware that gives you more clearance between the arm and inner fender.
These arms correct the suspension geometry by increasing much needed caster and
allow for a wider range of alignment adjustment. The tubular construction also
gives you more tire & shock clearance compared to the stock stamped
arm."
Uni-Ball Arm Specs:
- Tubular chromoly upper a-arms
- Uses Aurora 1.25" uniballs (Made in the USA)
- New flush mount hardware and spacers
- Uniball spacers CNC machined from heat-treated stainless steel
- Energy Suspension polyurethane bushings with thick inner sleeves
- Includes grade 8 and high strength 12pt hardware
- Stainless steel ABS line clamps
- Powder coated gray finish
Maximum wheel backspacing =
4.50"
Camburg
"Ball-Joint" Upper Control Arm Set: 379.00/pair
Replacement Ball-Joint Set: 145.00/pair
Looking to change out your upper control arms
without hitting the bank account too hard? Camburg now offers a performance
upper arm that utilizes the OEM type Toyota ball-joint. You re-use your factory ball
joint or we have new premium aftermarket joints available. It gives many of the same
benefits their uniball upper arms offer at a much lower cost. By building an
upper arm to re-angle the ball-joint, you’re able to gain more wheel travel
and keep the joint in its normal operating range. These arms also correct the
suspension geometry by increasing much needed caster which improves handling and
allows for a wider range of alignment adjustment. The tubular construction also
gives you more tire & shock clearance compared to the stock stamped arm.
Ball-Joint Arm Specs:
- Tubular chromoly upper a-arms
- Re-angled ball-joint to increase wheel travel over stock
- Increase in positive caster geometry for better handling
- Energy Suspension polyurethane bushings with thick inner sleeves
- Uses factory ball-joints and hardware
- Includes all necessary hardware
- Stainless steel ABS line clamps
- Powder coated gray finish
Camburg UCA Bushing Rebuild
Kit: 31.50
Includes all the poly bushings,
bushing sleeves and zirks needed to service a pair of upper control arms. No Uni-Balls
included, see below.
1" Uni-Ball Set
for Camburg UCA: 120.00
Includes two Uni-Balls,
will service a pair of UCA's. For the older arms with 1" uni-balls.
1.25" Uni-Ball
Set for Camburg UCA: 140.00
Includes two Uni-Balls, will
service a pair of UCA's. For the newer arms with 1.25" Uni-Balls.
Tri-Flow® Superior Dry Lubricant: 5.89
Tri-Flow® Superior Dry Lubricant is an elite formula created for dry
and dusty conditions. The 2oz drip bottle applicator
allows for deep penetration in hard to reach moving parts. Featuring paraffin
wax and high-grade petroleum oil to allow the lube to go on wet, but then set up
in a dry, 'wax-like' film so it will not attract or absorb grit and grime.
Perfect for dry, dirty, dusty conditions, while still providing adequate wet
weather performance. Holds up to extreme pressures and resists water wash-off.
Provides incredible efficiency without attracting an excessive amount of
contaminants. Great for Uni-Ball bearings.
___________________________
Timbren Front Suspension
Enhancement Kit: 195.00
Click HERE
for more info. FREE SECOND DAY FREIGHT ON THIS TIMBREN PRODUCT! Contact
us with your zip code if you don't need Second Day Freight and we'll get you
a price on the Timbren's with standard shipping.
___________________________
REAR SUSPENSION COMPONENTS
Sway-A-Way Rear Shock Set:
455.00/set
Extended Travel, Rebuildable, Revalveable,
Custom Valved, Nitrogen Charged Racing Shock Set From Sway-A-Way.
Bilstein 5100 Rear Shock
Set: 158.00/pair
These zinc coated high performance Bilstein
rear shocks are able to accommodate 0-2" of rear lift. Performance valved
to provide better handling.
Alcan Tacoma Leaf Spring
Set: 599.00/set
Comes with graphite impregnated self
lubricating poly bushings and U-bolts. Click
here for more details.
Deaver Racing 1.5" Lift
Leaf Spring Set:
599.00/set
Comes with graphite impregnated self
lubricating poly bushings and U-bolts. 10 leaf.
Click
here for more details.
Wheeler's 1.5" Lift 3 Leaf
Progressive Add A Leaf Kit: 149.95
A 3 leaf progressive Add A
Leaf set that replaces your factory overload leaf. Comes with longer U-bolts.
Wheeler's 1.5" Lift Add A Leaf Kit: 77.50
A single leaf set
made
specifically for the 05-current Tacoma. Diamond cut ends, anti-friction pads and
center pins included.
Timbren Rear Suspension
Enhancement Kit:
195.00
Click HERE
for more info. FREE SECOND DAY FREIGHT ON THIS TIMBREN PRODUCT! Contact
us with your zip code if you don't need Second Day Freight and we'll get you
a price on the Timbren's with standard shipping.
WE HAVE 1",
1.5" and 2" REAR BLOCK SETS, TOO!
|